1. Peel and stick the goldfish pattern piece on to the fabric you want to embroider.
2. Use a backstitch or stem stitch to stitch over the pattern lines.
3. Soak your stitched fabric in cold water for about 30 minutes and rinse away the stick-and-stitch paper.

1. Thread the needle with yarn and tie a knot in the other end. Starting on one side bring your needle through one hole and go across the loom to the hole on the opposite side. Then move over one hole and go back across the loom to the other side. Do this for all 5 holes.
2. Bring your needle through the hole in the opposite corner. Weave through the yarns over-under-over-under-over. Then bring the needle through the hole on the opposite side.
3. Move over one hole and repeat but do the opposite pattern: under-over-under-over-under. Repeat until you have completed all the rows.
4. Flip to the back and tie a knot. Put a dot of glue on your knots and then you can trim the yarn ends short.

1. Thread the beads onto the cord.
2. Hold one end of the cord in your left hand. Lay it to the right following your pointer finger and bring the other end up to make a loop.
3. Wrap the cord twice around your finger. The wraps go away from you and then through the center loop.
4. Bring the end to the left of the wraps and then through the two wraps from left to right.
5. Pull it tight. Tie an overhand knot on each end of the cord. Slide the cord through the knot to adjust the size.

1. Cut the wool felt bead in half. Please be careful! This makes 2 mushroom caps.
2. Tightly roll the felt rectangle like a cinnamon roll, starting at the short end to make a cylinder. Add a little glue to hold the roll together. Glue stick is ideal for this!
3. Thread your needle. Bring the needle through the top of the mushroom cap from top to bottom. Then go through the cylinder bead, add a glass bead and go back through the cylinder the opposite way. Stitch one more time through the mushroom cap from bottom to top.
4. Pull the thread so the pieces lay close together. Leave about 3 inches of thread at the top and tie the ends together to make a hanging loop.

1. Color your alpacas using your favorite art materials.
2. Carefully cut them out around the black line.
3. Add the legs by clipping the clothespins to the bottom
4. Stand them up!

1. Fold the ribbon in half and slip the folded ribbon over the split ring.
2. Sandwich the ends of the ribbon between the two felt pieces.
3. Use a running stitch to stitch around all four sides of the square through both layers of felt and the ribbon.

1. Tie a knot in one end of the cotton cord. Leave the top two holes empty. Bring the needle through the holes and zig zag across the loom making parallel lines of cord all the way from top to bottom. Tie a knot on the back.
2. Use the wool yarn to weave (over-under-over-under) into the cord warp threads. Push the rows of weaving tightly together.
3. Thread the remaining cord through the top two holes to make necklace cord for your pendant.

1. Carefully remove the paper wrappers from the ends of the thread skein. There is a cord tied underneath; do not remove the cord.
2. Slip the jump ring through the thread loops on both ends of the skein.
3. Gently rotate the ends of the ring to close the loops. They are soft enough you can do this with your fingers or a small pair of pliers.
4. Cut the skein in half to make two tassel charms.

1. Open the split ring and add the goat charm and lobster clip.
2. Thread the ribbon through the split ring and fold in half, matching the ends.
3. Tie both ends of the ribbon in an overhand knot and pull tight.

1. Open the hairclip and place the center of the ribbon at the top of the clip opening. Wrap the right side ribbon end over the outside of the clip, through the center and under the left side.
2. Now take the left side ribbon, wrap it over the outside of the clip, through the center and under the right side.
3. Repeat the same steps alternating the right and left ribbons. Push the braided ribbon towards the top of the clip.
4. When you have filled the clip, tie the ends of the ribbon together. You can leave the ribbons long for true retro style or trim them short.

1. Thread the cotton cord through the split ring. Fold the cord in half and match the ends.
2. Add a small ceramic bead, fish bead, small ceramic bead over both ends of the cord.
3. Slide the beads toward the split ring and tie both ends of the cord in an overhand knot. Trim the cord ends.

Handwoven bookmarks

Zipper pulls with fiber art puns

Yarn and sheep themed stickers

Pins with punny yarn and knitting jokes

Tiny fish stitch markers

Handprinted sheep art

Pom sheep keychains

Goldfish Magnet